Key Features:
- No of Pages: 59
- No of Chapters: 05
Introduction:
Abstract
The advantage of cellular communication like GSM technology is a potential solution for such remote controlling activities. GSM-SMS technology can be used to control household appliances from remote places. Remotely, the system allows the home owner to monitor and control his house appliances via his mobile phone set by sending commands in the form of SMS message and receiving the appliances status as well. This system provides ideal solution to the problems caused in situations when a wired connection between a remote appliance device and the control unit might not be feasible. The system is wireless and uses the user’s mobile handset for control and therefore the system is more adaptable and cost effective. The system uses GSM technology thus providing ubiquitous access to the system for appliance control. With this hypothesis, three different approaches have been proposed and implemented in this project; FIRSTLY, home control switch/household appliances are controlled by server mobile which acts as remote control. SECONDLY, GSM-SMS messaging technology is used to control them from remote places and FINALLY, to provide a multiple agents environment.
Table of Content
PAGES
TITLE PAGE i
CERTIFICATION ii
DEDICATION iii
ACKNOWLEDGEMENT iv
ABSTRACT v
TABLE OF CONTENT vi-vii
LISTS OF FIGURES viii-ix
CHAPTER ONE
1.0 INTRODUCTION 1
1.1 PROJECT OBJECTIVE 2
1.2 SCOPE OF THE PROJECT………………………………………………….........................3
1.3 OPERATION OF THE SYSTEM 4
1.4 ARCHITECTURE OF THE SYSTEM 5
CHAPTER TWO
2. 0 LITERATURE REVIEW 6
2.1 SYSTEM DESCRIPTION 7
2.1.1 USER GSM MOBILE HANDSET 8-11
2.1.2 RECEIVER GSM HANDSET 12-13
2.2 MICRO CONTROLLER BOARD 14
2.3 SWITCHING MODULE 15
CHAPTER THREE
3.0 SOFTWARE DESIGNING 16
3.1 TRANSFORMER 17-19
3.2 TRANSFORMER CALCULATION 20-26
3.3 RECTIFICATION PROCESS 27-30
3.4 MICRO CONTROLLER SECTION 31 -35
CHAPTER FOUR
4.0 TESTING 36
4.1 SYSTEM TESTING 37
4.2 PACKAGING 38
4.3 TROUBLE SHOOTING THE DESIGN 39
CHAPTER FIVE
5.0 PROBLEM ENCOUNTERED 40
5.1 PRECAUTIONS 41
5.2 RECOMMENDATION 42
5.3 CONCLUSION 43
5.5 APPENDIX 44
5.4 PROGRAMME CODES 45-55
5.6 REFERENCE 56
Introduction
Nowadays, people’s expectations in their life quality are increasing as the technology is improving rapidly. People need an affordable system (smart) that can make their lives easier, more comfortable, and offer more safety.GSM based home automation system is an electrical and electronic system designed to control home appliance with a mobile phone. The two main technologies applied in the system are GSM and PLC. GSM stands for global system for mobile communication and PLC stands for power line communication. In this study, Nokia 6100 is chosen as the GSM phone that receives command and transfers it to controller. Due to rapidly advancing of mobile communication technology and widely availability make it possible to incorporate mobile technology into home automation systems. ’’AT’’ command is used as communication between GSM phone and micro controller by passing through a serial interface RS232 with the help of its driver.
The project is based on the principle of GSM network, which enables the user to remotely control the operations of the appliances by using a mobile phone. In other word it would transform a normal home into an intelligent home. The controlling circuit is the most important component in communication and interface between home appliances. It was implemented by using peripheral interface controller (PIC) interfaced to mobile phone. The user can perform ON/OFF operations of the appliances just by pressing keypad of mobile phone.
The user sends GSM data in the form of SMS (short message service) message to switch ON or OFF any appliances at home such as lamp, air condition, fan and etc. the appliances may also provide the user with its current ON/OFF status. The system can be improved to provide the user with information about the status of each appliance
Buy Now
